Transition Networks 8-port 100BASE-FX switch Guide de l'utilisateur télécharger pdf (Page 70)

4-6.Updating Firmware using the Console Port

1. While booting the switch, press the X key to start the Xmodem routine on

the device.

2. Pressing X will cause the switch Xmodem application to begin and cause

the baud rate to change to 57600 bps. You will need to disconnect the

cable connected to the serial port, and change the baud rate of your

hyper-terminal application on your laptop to 57600 bps, then connect the

cable and reconnect to the switch.

3. Select “send file" under the "transfer" menu from menu bar.

4. Press the "browse" button to select the path.

5. Select "1K Xmodem" of protocol and press the "Send" button.

1 2 ... 65 66 67 68 69 70 71 72 73 74 75 ... 116 117

MIL-SM808GPxx 1
Table of Contents 4
Introduction 7
Web-based Management 10
SNMP Network Management 11
Hardware Description 12
Rear Panel 14
Network Application 16
Network Configuration 17
Console – Menu 18
4-1 Main Menu 20
4-2. Status and Counters 21
4-2-1. Port Status 22
4-2-2. Port Counters 23
4-2-3. System Information 24
4-3-1-1. Device Information 27
4-3-1-2. IP Configuration 28
4-3-1-3. Change Username 29
4-3-1-4. Change Password 29
4-3-4. VLAN Configuration 34
4-3-4-1. VLAN Configure 35
4-3-4-2. Create a VLAN Group 37
4-3-6-1.Static MAC Address 42
4-3-7.Misc Configuration 46
4-3-7-1.Port Security 47
4-3-7-2.MAC Age Interval 48
4-4-1.STP 53
4-4-1-1.STP Enable 53
4-4-1-2.System Configuration 55
4-4-2.SNMP 58
4-4-2-1.System Options 60
4-4-2-2.Community Strings 61
4-4-2-3.Trap Managers 63
4-4-3.GVRP 64
4-4-4.LACP 65
4-4-4-1.Aggregator Setting 66
4-4-4-2.State Activity 67
4-4-4-3.LACP Status 68
4-5.Reboot Switch 69
Web-Based Management 73
1. Home Page 75
5-2. Port status 76
5-3. Port Statistics 77
5-4. Administrator 77
5-4-1. IP Address 79
5-4-2. Switch Settings 79
5-4-2-1.Basic 79
5-4-2-2.Advanced 81
5-4-4. Port Controls 89
5-4-5. Trunking 89
5-4-5-1. Aggregator Setting 91
5-4-5-3. State Activity 92
5-4-6. Filter Database 94
5-4-6-1. IGMP Snooping 94
5-4-6-2. Static MAC Address 95
5-4-6-3. Port Security 96
5-4-6-4. MAC Filtering 97
5-4-7. VLAN Configuration 98
5-4-7-1. Basic 99
5-4-7-2. Port VID 101
5-4-8. Spanning Tree 103
5-4-9. Port Mirroring 106
5-4-10. SNMP 107
5-4-11.Security Manager 109
5-4-13. Configuration Backup 110
5-4-12. TFTP Update Firmware 110
5-4-14. Reset System 112
5-4-15. Reboot 112
Technical Specifications 113
Safety UL, cUL 114
Troubleshooting 115
 Cabling 117

Commentaires sur ces manuels

Pas de commentaire

Transition Networks 8-port 100BASE-FX switch Guide de l'utilisateur Page 70

Commentaires sur ces manuels